Ximi Elga

74LS164N DATASHEET PDF

74LSN from Fairchild Semiconductor. Find the PDF Datasheet, Specifications and Distributor Information. 74LSN Datasheet, 74LSN PDF, 74LSN Data sheet, 74LSN manual, 74LSN pdf, 74LSN, datenblatt, Electronics 74LSN, alldatasheet. These 8-bit shift registers feature gated serial inputs and an asynchronous clear. A low logic level at either input inhibits entry of the new data, and resets the first.

Author: Muzilkree Tygoll
Country: Ethiopia
Language: English (Spanish)
Genre: Literature
Published (Last): 9 April 2012
Pages: 321
PDF File Size: 16.9 Mb
ePub File Size: 2.7 Mb
ISBN: 735-6-48709-345-6
Downloads: 71141
Price: Free* [*Free Regsitration Required]
Uploader: Voodoozshura

The extreme top left pin from the printed side is the first pin in the order, and the pin just opposite to it on the other row is the last or the 14 th pin. I know there is a pull down and a pull up in the raspberry pi when you configure the GPIO as input, but is there a pull down when you are in output mode? Now suppose if through a simple wiring pins 1 and 2 are configured in such a way that when the last pin 13 of the IC goes high while sequencing serially, it grounds the serial input 1 and 2.

Take a peek at the data sheet. You might even need to replace the shift register, but probably not.

Unlike ordinary CMOS ICs which has also been discussed datashee many of my previous articlesthe above ICs are equipped with many different built-in features which may be accessed or activated by datasheet applying the appropriate logic inputs dagasheet components to their relevant pin-outs. For example if the pin — outs 1 and 2 are permanently connected to the positive supply and the reset pin is joined to the last output of the IC pin 13then, as discussed earlier, once all the outputs become high the last pin 13 instantly resets the whole circuit, shutting the whole array of outputs, and the cycle repeats.

Better yet, JamesMagnus, you have a scope. Introduction Through a few of my previous articles I have tried to cover the working principles of a couple of versatile ICs like the and So I added a schmitt trigger between the raspberry pi and the register clock input, and now it shifts exactly the number I want.

  COURS ELECTROTHERMIE PDF

I took some photos of the scope, the first is the clock from the GPIO without nothing and the second is the clock connected to the register. The serial inputs pin 1 and 2 of the IC has a special purpose of resetting the above procedure in an interesting pattern. A Low power Schottky input typically sits at about 1. Sign up or log in Sign up using Google. The measurement or what I think is the measurement number in all the screen shots says 3.

Home Questions Tags Users Unanswered. Post as a guest Name. By clicking “Post Your Answer”, you acknowledge that you have read our updated terms of serviceprivacy policy and cookie policyand that your continued darasheet of the website is subject to these policies.

That’s pretty far fetched, given the frequencies involved. Thanks for all your advices and suggestions, have a nice day. Hopefully you will get to see another article pretty soon, which will explain the practical utility of this wonderful IC. Perhaps this has something to do with 74ls64n problem.

74LSN Datasheet, PDF – Alldatasheet

In real I will put mosfets to control a big led board. Hopefully you will get to see another article pretty soon, which will explain the practical utility of this wonderful IC. Unlike ordinary CMOS ICs which has also been discussed in many of my previous articlesthe above ICs are equipped with many different built-in features which may be 74la164n or activated by just applying the appropriate logic inputs or components to their relevant pin-outs.

Now suppose if through a simple wiring pins 1 and 2 are configured in such a way that when the last pin 13 of the IC goes high while sequencing serially, it grounds the serial input 1 and 2.

This chip can’t drive the kind of current you want it to. Thus exceeding operating conditions, all bets are off. Hasn’t ever happened to me. You should test 74os164n the FETs in place.

  DSEI60 - 12A PDF

The serial inputs pin 1 and 2 of the IC has a special purpose of resetting the above procedure in an interesting pattern. Looks pretty clean but you need to zoom way in to know for sure. Through a few of my previous articles I have tried to cover the working principles of a couple of versatile ICs like the and Cleaning the pulse up with a Schmitt trigger got it working, but is masking the real problem – you Pi’s GPIO line is either not being controlled correctly by your program, or it’s blown up.

The whole output array, instead of shutting down all together, now starts receding sequentially one-next-to-the-other, until all of them are shut down to begin the cycle all over again.

How Would You Build Moving LED Signs Using IC 74LS? Pin-Outs Explored

The extreme top left pin from the printed side is the first pin in the order, and the pin just opposite to it on the other row is the last or the 14 th pin. The length of your clock wire might be a factor in this. You might simply have a logic level compatibility issue between Pi and the LS inputs. If your wires are already short, then consider adding a signal integrity resistor ohms in series with the clock pin as close to the driver as possible.

74LS164 – 8-Bit Shift Register Ser In/Para Out

What am I doing wrong? You are probably getting multiple pulses instead of just one. Similarly the IC requires only an external clock signal to make its outputs swing into action and produce interesting logic sequences.