Ximi Elga

AN6884 DATASHEET PDF

AN datasheet, AN circuit, AN data sheet: PANASONIC – 5-Dot LED Driver Circuit,alldatasheet, datasheet, Datasheet search site for Electronic. AN datasheet, AN pdf, AN data sheet, datasheet, data sheet, pdf, Panasonic, 5-Dot LED Driver Circuit. Description, 5-dot Led Driver Circuit. Company, Panasonic Industrial Company/ Electronic Components. Datasheet, Download AN datasheet. Cross ref.

Author: Doukasa Kibar
Country: Republic of Macedonia
Language: English (Spanish)
Genre: Automotive
Published (Last): 26 February 2007
Pages: 132
PDF File Size: 6.57 Mb
ePub File Size: 20.65 Mb
ISBN: 464-6-28420-147-4
Downloads: 8993
Price: Free* [*Free Regsitration Required]
Uploader: Tygokazahn

(PDF) AN6884 Datasheet download

There is also no discharge path with your arrangement. Passing Vin through a reverse capacitor seems to be potentially more prone to failure.

Can someone explain what the reversed capacitor is doing here? That’s clear, because the input in my test circuit is DC.

5+1 led vu-meter with AN6884

Post as a guest Name. Per AN’d datasheet. Post Your Answer An8684 By clicking “Post Your Answer”, you acknowledge that you have read our updated terms of serviceprivacy policy and cookie policyand that your continued use of the website is subject to these policies.

It sounds like you’re trying to drive this circuit with a signal that includes a considerable DC bias, which explains why all of the LEDs light up right away when you remove short out the capacitor. Right, I get that pin 7 is the output of the amp, but it’s part of the negative feedback loop on the amp. However, if that’s the case, I can’t explain why reversing the capacitor doesn’t work, unless the actual polarity of the capacitor is backwards from what you think it is.

It’s the DC bias determine the polarity.

By clicking “Post Your Answer”, you acknowledge that you have read our updated terms of serviceprivacy policy and cookie policyand that your continued use of the website is subject to these policies. To be clear, removing the capacitor doesn’t light up the LEDs all at once. Vref is the high an68844 of the 5 LED comparators in the datasheet block diagram. Indeed, it must in order for any of the LEDs to turn on!

  HP J5700 SCAN TO PDF

AN Datasheet(PDF) – Panasonic Semiconductor

As displayed, the LEDs go from fully off to fully on over roughly the entire turn range of the potentiometer. There’s still a much shorter range over which a varying number of LEDs come on. Have you tried a non-polarized capacitor e. By using our site, you acknowledge that you have read and understand our Cookie PolicyPrivacy Policyand our Terms of Service. You might want to edit to explain your answer a bit more. Email Required, but never shown.

Per AN’d datasheetPin 8 is the signal input pin, and it’s the internal Op amp’s positive input. The diode will mess up the response of the chip due to its forward voltage drop. It appears to be reversed. By “low side”, you’re referring to the inverting inputs of the comparators. Pin 8 is the signal input pin, and it’s the internal Op amp’s positive input.

You should fix the capitalisation of sentences and electrical units ‘F’ for farad to improve legibility and credibility. The LED pins connect to the negative side of the LEDs, and the pins go low when the output of the internal amp goes above Vref qn6884 by satasheet dividing resistors at each comparator. Setting 7 higher than ground biases the low side of the comparators, allowing them to turn on with a lower output from the amp.

(PDF) AN Datasheet PDF Download – 5-Dot LED Driver Circuit

If I remove the 2. This makes sense, but why not a diode? This circuit will light the LEDs as the input voltage on pin 8 increases relative to pin 7. Reverse biased capacitor on IC input pin Ask Question. Sign up using Facebook. Capacitor with polarity can be used ac couple or blocking. That means there is a small current flow out from the pin. I am looking at the test circuits on the data sheet for the AN VU meter IC, and I cannot understand the connection to pin 8 in the following diagram: If I “correct” the orientation, the circuit does datzsheet work at all.

  FUNGIA CANDIDA PDF

Your description doesn’t agree with that in the datasheet. I know the correct names, but I conversely find “inverting” and datwsheet confusing when dealing with comparators, since those terms make more sense when dealing with op-amps. Pin 8 accepts a positive input voltage.

Very confusing terminology, since the datashedt input can have a higher voltage than the noninverting input. Home Questions Tags Users Unanswered. Pin 7 is the output of the internal amplifier, and pin 8 is its input, designed to accept a low-level AC input 57 mV for a 0-dB indication. Most people use “low” to refer to either a lower voltage, or a lower position on the diagram.

So it determines the DC bias of the block capacitor’s polarity. Fadecomic 2 6. It just shortens the range of turn over which the potentiometer works. Sign up using Email and Password. How does doing anything to pin 7 or pin 8 affect that? I’m not reading it that way. The potentiometer is clear, but the 2.

I will be certain to use them here from now on. That is to say that the LEDs all come on at a much smaller turn of the potentiometer. Sign up or log in Sign up using Google.