Ximi Elga

ASTM B164 PDF

ASTM B specification covers Nickel Copper Alloys like Monel Alloy Round Bar with ASTM B UNS N in the form of hot-worked and cold- worked. Designation: B – 03 Standard Speci?cation for Nickel-Copper Alloy Rod, Bar , and Wire1 This standard is issued under the?xed. Monel is a corrosion resistant NiCu easily machined, and fabricated. ASTM B, ASTM B, QQ-N Class A, UNS N Available in bar, wire.

Author: Tygok Zulkitaur
Country: Liechtenstein
Language: English (Spanish)
Genre: Medical
Published (Last): 26 February 2012
Pages: 226
PDF File Size: 19.77 Mb
ePub File Size: 11.49 Mb
ISBN: 160-2-77099-187-1
Downloads: 80898
Price: Free* [*Free Regsitration Required]
Uploader: Vilkree

Pumps and valves used in the manufacture of perchlorethylene, chlorinated plastics.

In the annealed astmm UNS N Round Bars is an alloy that is easy to form and fabricate with no requirements for additional heat treatments to re-balance the alloy. The material shall conform to the chemical composition limits specified by the reference material. Hot-worked material to be machined in longer lengths should be speci?

Test Rounded Unit for Observed or Calculated Value Chemical composition, hardness, nearest unit in the last right-hand place of and tolerances when expressed in? Rod and Bar, All sizes A B 85 85 80 85 80 50 50 50 50 45 8B b1664 15 15B,C 15 30 30 25 35 — — — — — — — — 75 75 70 70 35 35 30 25 See This standard is atsm to revision at any time by the responsible technical committee and must be reviewed every?

Resistance to neutral, alkaline and acid salts is shown, but poor resistance is found with oxidizing acid salts such as ferric chloride.

In case of dissatisfaction with the results of the test, the producer or supplier may make claim for a rehearing. Link to Active This link will always route to the current Active version of the standard. Tensile strength and yield strength nearest psi 6. Intended primarily for hot heated bolts but is of somewhat inferior quality, as to surface seams and cracks compared to forging quality, see X1. Wire shall be excluded from these requirements. Material is thermally treated to relieve the major portion of the internal stresses resulting from cold-working and may have a very thin light to medium oxide.

  ALI HAMIDI CARP FISHING MASTERCLASS PDF

ASTM B Monel Alloy Round Bar Supplier · ASTM B UNS N

The permissible variations in diameter of cold-worked wire shall be as prescribed in Table 6. Machining Type Suggested starting rates are: One test per lot shall be performed for chemical analysis, tension test, hardness test, and wrapping test. If you feel that your comments have not received a fair hearing you should make your astmm known to the ASTM Committee on Standards, at the address shown below. Originally approved in ASTM does not give any warranty express or implied or make any representation that the contents of this abstract are accurate, complete or up to date.

Monel Round Bars is commonly used for valves, fasteners, tubing materials and mandrels. Rounds, squares, and rectangles up v164 12incl, and hexagons 21?

This standard has been approved for use by agencies of the Department of Defense. In the event of disagreement on the degree of back re? It is informational only and not an official part of the standard; the full text of the standard itself must adtm referred to for its use asfm application. Request quote on this grade.

Holes are to be drilled to midsection and the bottom of the hole shall be parallel to the entrant surface. Good resistance to sulfuric and hydrofluoric acids.

ASTM B – 03() Standard Specification for Nickel-Copper Alloy Rod, Bar, and Wire

No mechanical properties are offered since material asstm to be subsequently hot worked. High Performance Alloys stocks and produces Monel in this grade in the following forms: Last previous edition approved in as B – E All sizes 85 84 87 84 84 80 85 55 50 60 55 50 50 8B 10B 10B 20 20 20B,C 20 — — — — — — 80 75 75 — 70 — — UNS N 40 40 30 — 25 — — 30D 30 25 — 35 — — — — — B 75 to B95 — B 60 asym B75 — Cold-worked as worked or stress-relieved: It is particularly resistant to hydrochloric and hydrofluoric acids when they are de-aerated.

  BIOPELICULAS COMESTIBLES PDF

The purchaser shall have the right to perform any of the inspections or tests set forth when such inspections and tests are deemed necessary to ensure that the material conforms to prescribed requirements: This alloy is more resistant to nickel under reducing conditions and more resistant than copper under oxidizing conditions, it does show however better resistance to reducing media than oxidizing.

This abstract is a brief summary of the referenced standard. ASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentioned in this standard. Furnished in multiples of a speci?

MONEL 400 (UNS N04400) Ni 66.5 Cu 31.5 Description

Indications that appear between these points shall be evaluated on the basis aetm a straight line joining the two peak amplitudes. Wire shall not be out-of-round by more than one-half the total permissible variations shown in Table 6.

All wire shall wrap around a rod of the same diameter as the wire without cracking All wire up to 0. The distance between axtm jaws of the testing machine, with the specimen in place ready for testing, shall be not less than 10 in. Testing shall be done by a longitudinal wave or shear wave technique as speci?

Number of Tests Hot-worked Cold-worked Multiple lengths 6 to 24 ft 1.