Ximi Elga


Jominy end-quench test P. Le Masson, P. Rogeon, D. Carron, J.J. QuemenerIdentification du coefficient de transfert lors d’un essai Jominy instrumenté. Steel — Hardenability test by end quenching (Jominy test). Acier — Essai de trempabilité par trempe en bout (essai Jominy). Provläsningsexemplar. Project Number: Jominy End Quenching of Steel: The Effect of Time and Temperature on Austenitic Grain Growth. A Major Qualifying Project Report.

Author: Tygokree Nara
Country: Denmark
Language: English (Spanish)
Genre: Relationship
Published (Last): 10 August 2005
Pages: 49
PDF File Size: 7.73 Mb
ePub File Size: 2.87 Mb
ISBN: 327-2-91100-948-7
Downloads: 42238
Price: Free* [*Free Regsitration Required]
Uploader: Brazuru

The Jominy end-quench test was invented by Walter E. Jominy and A. Retrieved from ” https: The mainly common technique for measuring hardenability is the Jominy end-quench test. This results in a work-piece that does not have the same crystal structure throughout its entire depth; with a softer core and harder “shell”.

Heat Treatment Methods of steel. Hardenability does not refer to the most hardness that can be attained in the steels; that depends on the carbon content present in it.

Your email address will not be published. This information is plotted on a hardenability graph. Leave a Reply Cancel reply Your email address will not be published. Subsequent to cooling a flat surface is ground on the test piece and the hardenability is then found by measuring the hardness along the bar.

The hardenability of eszai ferrous alloy is measured by a Jominy test: Hardenability is specified by the hardness of the specimen as a function of distance from quenched end Refer fig. In other projects Wikimedia Commons. Substances like brine and water cool the steel much more quickly than oil or air. Manufacturing Engineering and Technology. Annealing Heat Treatment of Steels.

This page was last edited on 21 Esssaiat The hardenability of a metal alloy is the depth to which a material is hardened after putting it through a heat treatment process. When jominu hot steel work-piece is quenchedthe area in contact with the water immediately cools and its temperature equilibrates with the quenching medium.


From Wikipedia, the free encyclopedia. Steels with fine hardenability can be hardened more deeply below the surface and do not need high cooling rates.

The cooling rate will be highest at the end being quenched, and will decrease as distance from the end increases. Introduction to Forging Bulk Deformation of Metals. Jominy served as president of ASM in Change the order of display of dssai official languages of Canada English first French first Option to display the non-official languages Spanish or Portuguese Neither Spanish Portuguese Display definitions, contexts, etc.

Access a collection of Canadian resources on all aspects of English and French, including quizzes. By using this site, you agree to the Terms of Use and Privacy Policy.

File:Essai – Wikimedia Commons

The unit of hardenability is length. A laboratory procedure for jomin the hardenability of a steel or other ferrous alloy; widely referred to as the Jominy test. The farther away from the quenched end that the hardness extends, the higher the hardenability. The fluid used for quenching the material influences the cooling rate due to varying thermal conductivities and specific heats.

Precipitation hardening Heat treatment of steel. In result, the TTT curve is moved to the right, thus permitting very slower quenching rates during quenching.

History of Wind Energy Wind Power. Retrieved 9 December Language Portal of Canada Access a collection of Canadian resources on all aspects of English and French, including quizzes. The mechanism by which these alloying elements operate is to expand the time before the start of the austenite-to-pearlite transformation in the TTT diagram. It should not be confused with hardnesswhich is a measure of a sample’s resistance to indentation or scratching.

The inner depths of the material however, do not cool so rapidly, and in work-pieces jomny are large, the cooling rate may be kominy enough to allow the austenite to transform fully into a structure other than martensite or bainite. Therefore, the cooling curve is able to follow a less hastened path to the Ms line, more simply avoiding the nose of the TTT curve. It is a property that determines the depth under the quenched surface to which the steel is hardened well, or the severity of the quench necessary to achieve a definite hardness penetration.


File:Essai jominy.svg

Views Read Edit View joniny. FAQ Frequently asked questions Display options. The hardenability of ferrous alloys, i. It is an indication of how deep into the material a certain hardness can be achieved.

Modern materials and manufacturing processes. A collection of writing tools that cover the many facets of English and French grammar, style and usage. Alloying elements having the greatest result are chromium, manganese, molybdenum and nickel, to a lesser extent.

Hardenability – Wikipedia

The language you choose must correspond to the language of the term eszai have entered. A hardenability test in which a steel bar is heated to the desired austenitizing temperature and quench-hardened at one end and then measured for hardness along its length, beginning at the quenched end.

Heat Treatment Process of Steels. The geometry of the part also affects the cooling rate: Glossaries and vocabularies Access Translation Bureau glossaries and vocabularies.

Hardenability refers to the comparative capacity of a steel to be hardened by transformation to martensite form. If the fluid is agitated cooling occurs even more quickly.