Ximi Elga

FANUC 3T MANUAL PDF

This instruction manual describes preventive maintenance and quick FANUC SYSTEM 3T-MODEL C is designated to be assembled inside an NC machine. Fanuc System 3T-Model D Operator’s Manual(BE 02) – Free download as PDF File .pdf) or read online for free. I am looking for an operators manual for a Fanuc 3 T controller used on a small Wasino gang lathe. Any help would be appreciated. Going to.

Author: Mezik Shakinos
Country: Samoa
Language: English (Spanish)
Genre: Finance
Published (Last): 3 August 2015
Pages: 445
PDF File Size: 20.70 Mb
ePub File Size: 15.98 Mb
ISBN: 987-4-58005-261-7
Downloads: 11605
Price: Free* [*Free Regsitration Required]
Uploader: Felkree

You must set the tools using G50’s. Posted via Mobile Device.

I have a Fanuc 3T Maintenance manual but nothing Tsugami specific, Fanuc referred me to Tsugami, and those guys told me to talk to Remington Sales who disavowed all knowledge of this unit.

I’m wishing Fanuc had more info on these older units. I have 6T and 0T maintenance manuals but I dont suppose the parameter list from these will work or can some be used just to check fanucc the Hydraulics come on etc. I need the parameter list ffanuc get the machine working. But all of the information I can find seems to imply that its only used after major operations like replacing the servo or ballscrew and where you need to realign turrets and such.

Uncategorised MetalWorking Machines > Fanuc 3t manual

I would recommend manula you to create a thread asking manhal the parameter manual for your model. 3g there are process to set either the work offset or tool offset as relative to the absolute zero instead of the “random” zero? Somewere I have littutaure on gang tooling from a local dealer for famuc I mounted a Quick change tool post on the slide with a riser plate ok for short run’s with few tool’s Keep up th good work You can contact me ktaylor earthlink.

You will need it several times. MINP isn’t defined anywhere in the maintennace manual or the electrical manual. It started with the spindle seeming to pull manuxl and then fault out I could reset then the same I noticed that the load meater was going nut’s and I already had a noise to address in the motor I changed the bearing and dresed up the electrical conection’s inside and checked the tac pick up I wasen’t the first one to be inside it.

  DINKO SIMUNOVIC DUGA PDF

Follow us on All times are GMT Now from what can see, Tsugami may not have made the actual spindle. In any event, it seems to be new enough to support tool offsets. I know I had to tweak a bunch of parameters on mine because even though the original company bought a lot of options, it’s obvious they never used a lot of them since the related parameters either had default values or nothing.

Thanks fordav11, that worked! I tore into it pretty good, but I didn’t take apart the main spindle bearings since it spun cleanly up to RPM.

Fanuc 3t Manuals

And that zero is relative to the location of the table at poweron, not relative to the absolute machine zero. Program input is not started with the data input external start signal MINP.

Now does anybody know what is needed to upgrade to 80m? It’s taken about 6 months to get it fully operational, and now I’m ready to make its first cuts since it was torn apart and rebuilt. Thanks fomaz, I already have the original yellow floppy maintenance manual which theoretically describes all of the “non-option” parameters.

Let me know if there’s anything I can do to help you with your unit! G50 was the “magic”, I thought that only set max spindle speed, but it turns out on these older units, it also lets you specify the current location.

It looks like the spindle center is 2. I haven’t found any hardware manual for the PL3B’s, they’re kind of an orphan product. I’m working with a manual chuck for now and I have a collit spindel for it as well. Me Where exatly are you I’m in the midwest U. Ad text and spelling. We should also compare parameters and diagnostics. One last question, am I crazy for thinking of adding a C-axis to this machine? By roymanvega in forum Fanuc. I was figuring that you do the same thing on a lathe.

  ANSI Z765 PDF

From my admittedly limited understanding, I have the absolute zero which I can tweak with gridshift offsets, but does not seem to be used for anything except G28, e.

I have tool offsets which are settable from the MDI. Maybe you can tell me, a mystery item to me on the spindle is what looks like an air driven indexer. Machine Controllers Software and Solutions. It also lets you see the program as its running through it.

I have a RS set up from onother post printed and I will look for the post and forward Email ktaylor earthlink.

Fanuc 3t Maintenance Manual

IndustryArena uses cookies to ensure you get the best experience on our website. One last question for anybody still looking at this thread.

fankc Let me know if I can help with what documation I have. So if the table moves 1″, the readout said 2″. Fanuc paramater’s Yaddatrance are you in the US Location? I would like to find a manual that goes into the disambly of the head stock and slides.

Al to the rescue again: Results 1 to 12 of Didn’t realize that featurecam defaults to using its mznual radius compensation in addition to the radius compensation in the tool offsets so the part came out a hair oversize.

Anybody know if thats an option you can add afterwards? When you program the job make sure you have G28 U0 W0 at the end of each tool. There are some advanced tricks to avoid re-setting Manuxl for each job but start with this simple method first.