This tutorial is intended to give basic instruction on how to setup and run a Note: FloXpress will not work if the Flow Simulation add-in is currently installed. Solidworks FloXpress is a feature inside Solidworks that allows a designer simulate flow of fluids through a model. Based on the results of the. This simple tutorial is designed to show you the process of solidworks floxpress. The part that we use here is a simple part because our main goal is the process.
|Published (Last):||2 December 2014|
|PDF File Size:||5.9 Mb|
|ePub File Size:||2.65 Mb|
|Price:||Free* [*Free Regsitration Required]|
Click on the next button again. SWA home about contact us.
SOLIDWORKS Free Xpress Utilities-Part 4-FloXpress
Close the check geometry window. All of these articles will be stored in the category of Daily Dose…. Tloxpress did it too, now or part is a closed chamber.
From the report we can obtain properties such as maximum flow velocity. The check geometry window appears which indicates the smallest passage.
Tutorial – Using FloXpress in Solidworks? | GrabCAD Questions
Excellent floxpres tutorials with your Free Xpress Utilities series. Now there is a lid on one side. We are floxprees to close the two ends floxpreds the part so insert a new part just like below:.
First you must model the following part and I assume that you know the basics of solidworks 3d modeling. A new assembly opens, the begin assembly window appears with your part ready to insert, just click on the working area and your part will insert there. Click next and then click solve and wait. As you can see in the message box, the model is not ready for flow analysis. Now the part1 is added to design tree.
Once a pressure is selected, you can run the analysis to calculate flow velocity. Once we have created the lids we can then proceed to begin the simulation.
This simulations can be done using either pipes or bubbles. This free tool allows you to calculate how fluid or air flows through a part or assembly document. I will make sure that my future tutlrial have the links to read this themselves. Solidworks FloXpress is a feature inside Solidworks that allows a designer simulate flow of fluids through a model. The next step is to solve the model. From the results window you can simulate the trajectory of fluid particles as they move through the model.
Once the geometry is valid, you next select water or air as the fluid for the calculation. We then define the outlet conditions in terms of atmospheric pressure.
Tutorial – Using FloXpress in Solidworks?
Menu Home solidworks tutorial ebooks solidworks 3d sketch-1 solidworks sheetmetal-1 solidworks loft-1 solidworks flowxpress-1 solidworks photoworks-1 solidworks motionstudy solidworks drawing-1 solidworks 3d-sketch-2 solidworks assembly-1 solidworks loft-2 solidworks 3d-sketch-3 solidworks loft-3 solidworks assembly-2 solidworks surface-1 solidworks surface-2 solidworks sheetmetal-2 solidworks assembly-3 solidworks simulation-1 solidworks advanced loft solidworks drawing 2 solidworks toolbox solidworks pattern solidworks surface 3 solidworks simulation 2 solidworks helix.
The part that we use here is a simple part because our main goal is the process of floxpress.
The boundary conditions are also clearly described in the report. Use this information in conjunction with experimental data and practical experience. Do the same for the other side and we will be ready for floxpress. The Solidworks FloXpress icon is located under the evaluate tab. Right click on it and select edit part:.
solidworks tutorial flowxpress #1
The FloXpress wizard has a procedural sequence that enables the user maneuver through the simulation with ease and comprehensively understand the simulation. You can also choose to generate a report from the FloXpress simulation by simply clicking on the generate report icon at the bottom of the results tab.
This simple tutorial is designed to show you the process of solidworks floxpress. Define a plane parallel to the end face of the part and set the mm offset distance. Floxpresss went with a C-D Nozzle geometry for this demonstration. Next we choose the fluid that would flow through the model. Home Support Daily Dose June 17, by Chris Taylor. Share this with your friends.
Now the part is ready. The first step is to ensure that the model has no openings fully closed with lids. Home solidworks tutorial ebooks solidworks 3d sketch-1 solidworks sheetmetal-1 solidworks turorial solidworks flowxpress-1 solidworks photoworks-1 solidworks motionstudy solidworks drawing This was a very simple flow analysis.