FS2Crew PMDG NGX “Button Control” Tutorial. Flight The following is a very basic guide designed to help new FS2Crew NGX users. The following is a very basic guide designed to help new FS2Crew NGX users make a simple flight from A to B using Button Control. The tutorial does not cover . FS2Crew PMDG NGX “Voice Control” Tutorial The following is a very basic guide designed to help new FS2Crew NGX.
|Published (Last):||16 November 2015|
|PDF File Size:||7.23 Mb|
|ePub File Size:||11.88 Mb|
|Price:||Free* [*Free Regsitration Required]|
Tutorial for custom sounds in FS2CRew? – Airbus General – AEROSOFT COMMUNITY SERVICES
But I do not see where the instructions are to do this. This zip will substitute a blank STAR2.
Leave the other fields unchanged. I will try again tonight and report back. Try to get the Landing Flap out before feet. I’d like to run reboot in Button mode, is there a list available to indicate when to press the main and secondary buttons other than reading each page fs2rcew the manual.
Anyone have this or can point me to it? Approximately miles back of our arrival, RJAA, start setting up for the arrival. If running other programs that control aircraft doors tutirial add co-pilot sounds such as FSPassengersdisable their ability to control doors and disable their co-pilot voices.
Make sure the parking brake is set. The aircraft already has the correct fuel load for the flight. Found 63 files 7 pages Jump to page: As you approach the airport, press the Main Button to call for Fs2creq 1, then bring the back the speed in the autopilot speed window as necessary. That folder belongs to the Airbus, not to FS2Crew.
With approximately 2 minutes remaining to departure, the FA will phone the flight deck to tell you the cabin is ready. The outer doors will then open and the jetway will automatically connect to the aircraft.
None of the other buttons will work until FS2Crew has been activated. When lined up and ready to go, press the Main Button again to say: When ready to start your descent, adjust the autopilot panel accordingly.
Bryan York and Patrick Zwarts Size: Archived This topic is now archived and is closed to further replies.
Hello, adding custom sounds to FS2Crew is not possible.
FSX FS2Crew NGX 737 PMDG Mini Tutorial
Note that a mini-panel of the landing gear panel will pop up. When entering the runway, press the Main Button once to call for the runway entry procedure. The clickable hidden clickspot is located directly over the name of the SID.
You can f2screw try different voices in the airbus config settings. The voices of the FS2Crew simulation you can not change. Yeah, I knew I could change the region. Run the Before Takeoff checklist with the Main Button. tutkrial
FO will toggle the seat belt signs and turn on the landing lights. When the aircraft loads, the engines will be off assuming you loaded the FS2Crew Tutorial situation flight. After being cleared to pressurize, the FO will automatically perform his flow: When finished talking to the Engineer, the FO will automatically challenge you on the first Shutdown Checklist item. Thanks for clearing that up. Do not forget to do that! Perhaps change a few other voices or audio files. Also I used the FAA ‘point’ instead of ‘decimal’ in the clearances for CYYZ – this is also rectified and finally an essential update to the IAPs which had been incorrectly named in the original upload.
Tutorrial not alter selections on the PB Panel. FS2Crew will handle them!
The Engine Start procedure is semi-complex. Tutorial for custom sounds in FS2CRew? Graham K Jackson Size: FO will perform his takeoff flow. Tktorial 10, Flaps 5, Flaps 1, Flaps Up. Next, press the Main button once —and only once- to call for the Shutdown Checklist. Important Notes about Yellow Dots and Checklists: Use the Main Button to respond and complete the Shutdown checklist. You, as the captain, are responsible for the following during Pre-Flight: