Ximi Elga


A datasheet, A pdf, A data sheet, datasheet, data sheet, pdf, Intel, Multimode DMA Controller. Data Sheet for DMA Control Unit. REL iWave Systems Technologies Pvt. Ltd. Page 2 of (Confidential). DOCUMENT REVISION HISTORY. Revision. DATASHEET. The 82C37A is an enhanced version of the industry standard. A Direct Memory Access (DMA) controller, fabricated.

Author: Juzilkree Zulkizuru
Country: Djibouti
Language: English (Spanish)
Genre: Sex
Published (Last): 9 May 2004
Pages: 180
PDF File Size: 19.91 Mb
ePub File Size: 5.69 Mb
ISBN: 558-3-53630-954-2
Downloads: 38927
Price: Free* [*Free Regsitration Required]
Uploader: Aram

Although this device may not appear as a discrete component in modern personal computer systems, it does appear within system controller chip sets. DMA transfers on any channel still cannot cross a 64 KiB boundary.

Retrieved from ” https: This technique is called “bounce buffer”. The transfer continues until end of process EOP either internal or external is activated which will trigger terminal count TC to the card. In single mode only one byte is transferred per request. For every transfer, the counting register is decremented and address is incremented or decremented depending on programming. As a member of the Intel MCS device family, the is an 8-bit device with bit addressing.

Like the firstit is augmented with four address-extension registers.

Intel – Wikipedia

However, because these external latches are separate from the address counters, they are never automatically incremented or decremented during DMA operations, making it impossible to perform a DMA operation across a 64 KiB address boundary.

For datashwet mode of transfer, the width of the data bus is essentially immaterial to the as long as it is connected to a data bus at least 8 bits wide, for programming the registers. This happens without any CPU intervention. The operates in four different modes, depending upon the number of bytes transferred per cycle and number of 823 used:. In auto initialize mode the address and count values are restored upon reception of an end of process EOP signal.


A Datasheet pdf – Multimode DMA Controller – Intel

Because the memory-to-memory DMA mode operates by transferring a byte from the source memory location to an internal temporary 8-bit register in the and then from the temporary register to the destination memory location, this mode could not be datasjeet for bit memory-to-memory DMA, as the temporary register is not large enough.

By using this site, you agree to the Terms of Use and Privacy Policy.

From Wikipedia, the free encyclopedia. Memory-to-memory transfer can be performed. In general, it loses any overall speed benefit associated with DMA, but it may be necessary if a peripheral requires to be accessed by DMA due to either demanding timing requirements or hardware interface inflexibility.

Each channel is capable of addressing a full 64k-byte section of memory and can transfer up to 64k bytes with a single programming. Additionally, memory-to-memory bit DMA would require use of channel 4, conflicting with its use to cascade the that handles the 8-bit DMA channels. The is a four-channel device that can be expanded to include any number of DMA channel inputs.

It is used dwtasheet repeat the last transfer.

At the end of transfer an auto initialize will occur configured to do so. The channel 0 Current Address register is the source for the data transfer and channel 1 and the transfer terminates when Current Word Count register becomes 0. Consequently, a limitation on these machines is that the DMA controllers with their companion address “page” extension registers only can address 16 MiB of memory, according to the original design oriented around the CPU, which itself has this same addressing limitation.


Auto-initialization may be programmed in this mode. So that it can address bit words, it is connected to the address bus in such a way that it counts even addresses datsheet, 2, 4, The is capable of DMA transfers at rates of up to 1.

Intel 8237

For example, the P ISP integrated system peripheral controller has two DMA internal controllers programmed almost exactly like the When the counting register reaches zero, the terminal count TC signal is sent to the card.

Views Read Edit View history. This means data can be transferred from one memory device to another memory device. This page was last edited on 21 Mayat The IBM PC and PC XT models machine types and have an CPU and an 8-bit system bus architecture; the latter interfaces directly to thebut the has a bit address bus, so four additional 4-bit address latches, one for each DMA channel, are added alongside the to augment the address counters.

In an AT-class PC, all eight of the address augmentation registers are 8 bits wide, so that full bit addresses—the size of the address bus—can be specified.