Ximi Elga

ISO 6194-2 PDF

BS ISO Rotary shaft lip-type seals incorporating elastomeric sealing elements. Vocabulary. standard by British Standard. holes and shafts. ISO , Fluid power systems and components — Vocabulary. ISO , Rotary shaft lip-type seals — Part 2: Vocabulary. ISO (E) ISO’s member body in the country of the requester. .. ISO , Rotary shaft lip-type seals — Part 2: Vocabulary.

Author: Tam Kigakree
Country: Sudan
Language: English (Spanish)
Genre: Travel
Published (Last): 27 September 2007
Pages: 438
PDF File Size: 4.17 Mb
ePub File Size: 13.85 Mb
ISBN: 853-3-43490-971-1
Downloads: 48915
Price: Free* [*Free Regsitration Required]
Uploader: Baramar

BS ISO 6194-2:2009

Typically, the shaft rotates, and the housing is stationary, although in some applications the shaft is stationary, and the housing rotates. For undated references, the latest edition of the referenced document including any amendments applies.

Details of the software products used to create this PDF file can be found in the General Info isi to the file; the PDF-creation parameters were optimized for printing. Dry-heat ageing in air Time: Avoid unnecessary stretching of the spring during installation careless handling protect the rings during transport and storage 8.

In dusty atmosphere, use a dustproof lip. A list of organizations represented on this committee can be obtained on request to its secretary. The test shaft and seal housing shall simulate the envisaged maximum eccentricities specified by the customer.

Seal drawing reference or specification: The Manufacturer reserves the right to introduce changes, according to new technical solutions and progress in the area of technologies and materials. It is the responsibility of the user of this part of ISO to establish appropriate safety and health practices and to ensure compliance with any national regulatory conditions.


BSI also holds the copyright, in the UK, of the publications of the international standardization bodies.

ISO 6194-2:2009

We would be grateful if anyone finding an inaccuracy or ambiguity while using this British Standard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. The result shall be the specified nominal hardness see 4. Users are responsible for its correct jso. An example of a seal test report for a dynamic test is shown in Annex A.

ISO – Standards Australia

Whilst this part of ISO does not purport to address all the safety problems, if any, associated with its ios, attention is drawn to the need to employ sensible precautions while handling hot and cold fluids and equipment.

Damaged spring incorrect installation use proper installation methods. This study provides primarily information on this matter, which will enable the user to move in the maze of materials and catalogues of individual manufacturers.

Ensure that the batch oso elastomer has been tested in accordance with Clause 7. An example of a seal test report for the dynamic low-temperature test is shown in Annex B. NOTE Seal performance can be influenced by operating and environmental conditions beyond the scope of this test.

The result shall be the specified nominal density see 4. ISO consists of the following parts, under the general title Rotary shaft lip-type seals incorporating elastomeric sealing elements: The materials used for tests shall be in an unused condition.

Key 1 handle 2 seal housing 3 test fluid 4 test shaft 5 washer 6 spigot 7 plain hexagonal nut 8 washer 9 test seal 10 base 11 holes to locate with pins in base plate of refrigeration unit Figure ios — Typical example of dynamic low-temperature test fixture www. For lifetime performance testing, duration will be extended in agreement between purchaser and supplier.


BSI offers members an individual updating service called PLUS which ensures that subscribers sio receive the latest editions of standards.

Unless otherwise agreed between the supplier and purchaser, tests shall be in accordance with 7. The test specimens shall be similar to those used for the hardness test io 7. Buying isi Orders for all BSI, international and foreign standards publications should be addressed to Customer Services. The housing and the rotating member shall be capable of reproducing the eccentricity and off-set specified in 4. Find the desired size. Profile method ios Rules and procedures for the assessment of surface texture [6] ISOPetroleum products — Determination of knock characteristics of motor and aviation fuels — Motor method [7] ISOPetroleum products — Determination of knock characteristics of motor fuels — Research method [8] ISO If the dimension of the test piece is greater than 4 mm, then the normal test procedure shall be used.

This uso of ISO specifies general test requirements for rotary shaft lip-type seals. The data present in this study are for information only. Adobe is a trademark of Adobe Systems Incorporated.