Ximi Elga

ISO 7816-2 PDF

ISO/IEC specifies the dimensions and locations for each of the contacts on an integrated circuit card of an ID-1 card type. It also provides. ISO describes the physical characteristics of smart chip cards. It includes accommodation of exposure limits for electromagnetic phenomena such as. ISO is one of most important standards in the smart card industry. Parts of ISO specify physical characteristics, dimensions and location of the.

Author: Taubei Yolabar
Country: Senegal
Language: English (Spanish)
Genre: Health and Food
Published (Last): 10 April 2007
Pages: 438
PDF File Size: 12.93 Mb
ePub File Size: 1.68 Mb
ISBN: 890-5-21796-420-6
Downloads: 63811
Price: Free* [*Free Regsitration Required]
Uploader: Fenridal

The first three parts in particular are well established and allow total physical and electrical interoperability as well as defining the communication protocol between the IC card and the CAD Card Acceptor Device.

It specifies the standard method to maintain and query the database, it also provides format definitions. The guard time is defined to be equal to two bit periods although for block mode it can be changed to a 1 bit period.

The specification requires this voltage to be discharged across each of the contacts in both normal and reverse polarity.

ISO Introduction

Cards with contacts — Physical characteristics”. This standard in its many parts is probably the most important specification for the lower layers of the IC card. It further defined the concept of sleep mode not covered by ISO where the IC chip can reside in a latent mode preserving volatile memory contents with a maximum power consumption of uA.

ISO Design and use of identification cards having integrated circuits with contacts The ISO standard defines a single line for the interchange of data between the IC and the interface device. The test voltage is defined to be 1. One of the issues surrounding the use of the IC card relates to the temperature range for operational use. Introduction To Smart Cards – Page 2. Although the PC operates in full duplex mode. Retrieved from ” https: Mail this article Print this article.

  ECOSAN TOILETS PDF

This standard applies to the ID – 1 identification card specified in ISO and includes cards which may have embossing or magnetic stripes.

The 7816 Standard

Created inupdated inupdated in The three most widely used tests applied by fabricators are specified in the annex to the standard: We have previously discussed the position and definition of the IC connector and have identified eight contacts of which six are currently defined. ISO Identification cards numbering system and registration procedure for issuer identifers The ISO standard aligns with the use of two widely used external clock frequencies, 3.

According to its abstract, it specifies a card application. The physical properties of the contact IC card are referenced against earlier card standards and we will look at each of them in turn.

These specifications are defined by ISO as part three of the standard. This anomaly has been a source of irritation and it is now widely agreed that the IC connector should be on the front of the card. As the title implies, this part of the standard specifies the location of embossed characters on an ID -1 card for which two areas are assigned.

The embossing is defined to be on the front of the card and therefore on the same side as the IC connector. Related Posts Smart Card. Return to page 1. This means that the line must change direction depending on whether the IC is transmitting or receiving.

Cancel reply Your email address will not be published.

Data Layout on Magnetic Stripe Cards. The ISO family includes eleven parts which are in a constant state of flux as they are subject to revision and update. Part 5 Location of read – write magnetic track – track 3. It ay use biometric methods and standards to achieve personal identification. Technical Adviser to Smart Card News.

  BALZAC GOBSECK PDF

With a periodicity of 30 bendings per minute the card is deflected to 2cm at its centre from the long axis and 1cm from the short axis. The RSC interface however defines two separate wires for data transmission and reception which would need hardware modification in order to interface with the single wire IC card directly. Got Something To Say: The transmission of a single character defined as 8 bits requires an overhead of several bits as follows: Created inupdated inamended in The ISO standard defines the location of contacts and dimensions.

The ISO standard is meant for personal identification of the user. While we are all familiar with the use of imprinters to obtain a printed version of the embossed characters on some paper voucher, their viability on an IC card must be questionable.

There have been problems in the past with terminals supplying the wrong programming voltage with somewhat drastic effects.

Commands and mechanisms for security operations”. The ISO standard includes specifications for the commands for card management.

ISO part 2 smart card standard

By using this site, you agree to the Terms of Use and Privacy Policy. From Wikipedia, the free encyclopedia. This standard has the same scope as part 4 except that it defines the read – write track 3.

Area 2 is provided for the cardholder identification data such as his name and address.

ISO/IEC 7816

This standard is in five parts and covers the specification of the magnetic stripe and the card embossing. Variation in thickness or even slight warping of the card can cause communications failure.

The electronic properties and transmission characteristics of the IC card are fundamental to interoperability.