Ximi Elga


View and Download LUX TX Series installation and operating instructions online. TX Series Thermostat pdf manual download. Thermostats such as the Lux , the Smart Temp , TX, Lux HP are functional energy saving tools, but when Follow these instructions to reprogram it to the schedule you want. My Lux TX E is locked – how do I unlock it?. Buy Lux TXE for the lowest price available online! Presenting the new Lux ® TXE, a programmable thermostat that allows users to easily Manuals (3).

Author: Faular Kesho
Country: Gabon
Language: English (Spanish)
Genre: Travel
Published (Last): 13 September 2013
Pages: 127
PDF File Size: 11.30 Mb
ePub File Size: 18.87 Mb
ISBN: 920-5-83989-131-2
Downloads: 6745
Price: Free* [*Free Regsitration Required]
Uploader: Shaktimi

LUX TX500 Series Installation And Operating Instructions

Thanks for letting us know. This warranty gives you specific legal rights and you may also have other rights which vary from state to state. These same programming steps for all four periods must be performed in both Heat and Cool Temperature modes independently. Related questions Why thermostat turns off during hottest part of day yet runs fine at night?

Wiring Diagrams Limited Warranty: To create this article, 15 people, some anonymous, worked to edit and improve it over time. Our web site offers you answers to the most common technical questions, and also permits you to email your questions to our technical support staff at your convenience. When they are all labeled, carefully remove the wires one at a time, making sure that they do not fall back inside the wall.

The Temperature mode switch has three positions: When any of the following items are changed, the hardware reset button must be pushed for the change to be recognized. You will begin with the start time of the MORN period, and use the same procedures that were performed while setting the Nanual Program periods, using the NEXT button to advance through the values. Do not locate in a damp area.


In the summer, set the switch to COOL to control your air conditioner. Remove lu label wires one at a time. When finished, hang the top of the unit by the tabs at the top corners of the base, then snap the bottom of the unit into place.

On the side, there should be a green button with an arrow facing upwards and a red arrow facing downwards. Already answered Not a question Bad question Other. Generally, the B and O terminals are only used for Heat Pump systems. Do not use unnecessary force. Fill wall opening with non-combustible insulation to prevent drafts from affecting the thermostat. Loosen all screws on the old thermostat and remove it from the wall. The time amount for this delay is fixed at 5 minutes between on or off load changes.

Do not locate where air circulation is poor, such as in a corner or an alcove, or behind an open door. Hold the base against the wall.

Lux Products TXE manuals

Comments to this Manuals Your Name. The thermostat screen is blank except for the horizontal and vertical lines. Do not locate in unusual cooling conditions, such as: In the winter, set the system switch to HEAT to control your heating system.

You will be programming both Saturday and Sunday at the same time. When the Keylock is activated, a padlock icon will be visible in the area above the clock as shown below. Do not install it where there are unusual heating conditions, such as: This plastic may or may not be present, and is evident by the appearance of fake digits appearing on the display screen.


An Override may be cancelled by rotating the dial, changing the Temperature mode switch, or by initiating a Temperature Hold. Do not turn electricity back on until work is completed. It will then change to cooler “comfort” settings – all automatically, at.

Press “Next” to set the time and manua, use the “Up” and “Down” keys to select the correct time. It cannot be used with 3-wire zone valves, volt heating systems, or multi-stage heat pumps.

When you are finished performing your installation and setup options, please remove the thin plastic film that is protecting the LCD display screen on the front of the thermostat. Attach tx50e base to the wall with the two screws provided. Return the dial to the RUN position once you are finished setting the filter life.

A smaller swing number increases the number of cycles per hour, so the room temperature is more precise and constant. Got it, continue to print.

Do not locate where air circulation is poor, such as: By continuing to use our site, you agree to our cookie policy. Wires must be labeled before. If this unit fails because of defects in materials or workmanship within three years of the date of original purchase, LUX will, at its option, repair or replace it. This button can be pushed with a pencil or the end of a paper clip. Once a Hold is initiated, the thermostat will maintain the Hold set temperature indefinitely.