DWLAP. b/g Access Point. Command Line Interface Reference Manual. First Edition (January ). RECYCLABLE. Step 1 Open your web browser such as Internet Explorer and enter the IP address of the DWLAP in the Address bar and press Enter. The default IP. Access Point Mode The DWLAP is set to Access Point (AP) mode by default , which allows the DWLAP to connect to wireless clients.
|Published (Last):||12 December 2007|
|PDF File Size:||12.51 Mb|
|ePub File Size:||10.34 Mb|
|Price:||Free* [*Free Regsitration Required]|
Table of Contents Product Overview Using a power supply with a different voltage than the one included with the DWLAP will cause damage and void the warranty for this product. If any of the above items are missing, please contact your reseller. Manula Receptor Used to connect the supplied power adapter.
Installation Installation Considerations D-Link Air lets you access your network from anywhere you want. However, keep in mind, that range is limited by the number of walls, ceilings, or other objects that the wireless signals must pass through. Typical ranges vary depending on the types of materials and background RF noise in your home or business. Insert one end of the cable to the Ethernet port on the back panel of the DWLAP and the other end of the cable to your network switch or router.
You may use the web-based configuration or the AP Manager software to configure your access point.
Please refer to page 52 to use the AP Manager software. These buttons appear on most of the configuration screens in this section. Please click on the appropriate button at the bottom of each screen after you have made a configuration change.
Access Point Mode Wireless Band: Access Point is selected from the drop-down menu. The SSID can be easily changed to connect to an existing wireless network or to establish a new wireless network. Auto Channel Select Enable or Disable. Enable this feature to auto-select the Scan: Select Open System to communicate the key across the network.
Select Disabled or Enabled. Disabled is selected here. Select bit, bit, or bits.
D-Link Technical Support
Select the 1st through the 4th key to be the active key. Input up to four keys for encryption. Group Key Update Select the interval during which the group key will be valid.
A lower interval may reduce d-ljnk data rate. WDS Wireless Distribution System allows access points to communicate with one another wirelessly in a standardized way. It can also simplify the manuzl infrastructure by reducing the amount of cabling required. Enabling this feature broadcasts the SSID across the network. All devices on the network must share the same channel.
D-link DWL-2100AP Manual
The wireless adapters will automatically scan and match the wireless setting. WDS is selected from the pull-down menu. The SSID can be easily changed to connect to an existing wireles network, or to establish a new wireless network.
You will select one of these First through Fourth keys in the valid key field. AP Repeater Wireless Band: Select AP Repeater from the drop-down menu. The channel used will be displayed. The channel will follow the root AP. This feature is not available in Repeater mode.
AP Client Wireless Band: Select AP Client from the drop-down menu. This is considered your internal network. These settings may be referred to as private settings. Dynamic DHCP is chosen here. This field is unavailable when DHCP is chosen.
Advanced Performance Settings Wireless Band: Beacons are packets sent by an access point to synchronize a network. Specify a beacon interval value. The default is recommended. This value should remain at its default setting of If you encounter inconsistent data flow, only minor modifications to the value range between and are recommended Transmit Power: Choose full, half -3dBquarter -6dBeighth -9dBminimum power. Check if all wireless devices are Select Disabled to disable the filters function.
Internal Station Enabling this feature allows wireless clients to communicate with Connection: If this is disabled, wireless stations of the selected band are not allowed to exchange data through the access point. IP addresses automatically without the need to manually assign new IP addresses. Input the first IP address available for assignment in your network. Server translates domain names such as www. An example of a domain name is: IP addresses automatically without the need to manually assign IP addresses.
The DNS translates domain names such as www. Enter a user name. The default setting is admin. Enter the current password blank by default. Upgrade Firmware Update File: After you have downloaded the most recent version of the firmware from http: Select the file and click OK to update the firmware.
Configuration File Update File: Browse for the configuration settings that you have saved to your hard drive. Click OK after you have selected the settings file. Load Settings to the Click OK to save the selected settings to your hard drive. When you click Browse x-link the previous screen, the dialog box shown above appears.
Select the file you wish to download and click Open. When this dialog box appears, click Save and select a location to save the configuration file. This window displays the statistics of the IEEE Displays the MAC address of the client. System Log The log information will include, but not limited dwl-2100aap, the following items: Enter the IP address of the log server. Check the box for the type of activity you want to log.
There are three types: System Activity, Wireless Activity, and Notice. With AP Manager there is no need to configure devices individually. To launch the AP Manager: To select a single device, simply click on the device you want to select.
To select multiple devices, hold down the Ctrl key while clicking on each additional device. To select an entire list, hold the Shift key, click on the first AP on the list and then click on the last AP on the list. Device Configuration Click on this button to access the configuration properties of the selected device s. The device configuration window allows you to configure settings but does not actually apply the settings to the device unless you click the Apply button. You can also save and load configuration files from this window.
This allows you to change the device name for the selected access point. You must place a checkmark in the Device Name box to change the name. This pulldown selection enables or disables the ability to Telnet into the selected device s.
SNMP mnual disabled by default.
Dlink DWL-2100AP User Manual
The Service Set network Identifier of mxnual wireless network. Allows you to select a channel. Allows you to enable or disable the broadcasting of the SSID to network clients. Select Short and Long default or Long Only. A pulldown menu to select the maximum wireless signal rate for the selected devices s. Specify the beacon value for the selected device s here.